COMING SOON

A 280ml bone china flat-bottom dripper for 1 to 4 servings, made to sit on a transit base for switch-controlled brewing or a bamboo holder for a standard pour over

A flat-bottom pour over drains evenly when the coffee bed stays level and water can exit across the whole base. Uneven flow usually starts where the filter meets the brewer: the paper folds against the wall, fines collect in the center, and the middle of the bed slows while the edges drain through.

The Tri-Spin FS Flat Dripper from DragonFly Design Center, also known by its Chinese name 三旋空玄武 (Xuanwu), is a new bone china flat-bottom brewer designed to keep that flow even. Its transit base lets you brew as a standard pour over, or close the knob and steep as an immersion.

How the Tri-Spin FS Manages Flow

Inside the dripper, 20 raised ribs hold the filter paper off the wall so it keeps its shape through the brew. With the paper supported, water moves through the bed at a more consistent rate, and results vary less from one brew to the next.

The wall angle is set to keep the flow rate quick while still allowing a finer grind. A finer grind raises extraction yield, so a faster drawdown can still reach a full extraction and keep a clear, layered flavor.

At the base, DragonFly's Tri-Spin hollowed design spreads the water's exit points across the base rather than concentrating them in the center. This reduces clogging and keeps water moving through the whole bed instead of stalling in the middle, which matters most at larger doses where localized over-extraction is more likely.

The dripper received a German Design Award in 2026.

The Shanwen Jia Exterior

The outer wall carries the Shanwen Jia (山文甲) pattern first used on the CT62. Shanwen Jia, also known as Shanwen Armor, is a Tang Dynasty armor recognized by its repeating mountain pattern. On the dripper, that pattern wraps the outer wall as a continuous geometric repeat.

The exterior is the link between the two brewers. The CT62 pairs it with a conical interior, and the Tri-Spin CT pairs it with a flat bed and a grooved wall.

Product Details

Brewing with the Transit Base

With the Transit Base open, it brews as a fast-flowing flat-bottom pour over and gives a clean, filter-style cup. With the switch closed, water stays in contact with the grounds until you open it, which gives a fuller, immersion-style cup.

Immersion is a forgiving starting point while your pour technique is still developing. The open setting gives experienced brewers direct control over pour rhythm and timing.

You can also choose to brew with a Bamboo Dripper Holder – using it as a traditional pourover dripper.

DragonFly Tri-Spin FS Flat Bottom Dripper - 280ml brews 1 to 2 servings, and takes 185 flat-bottom paper filters. It is available in Shell Pink, Black, and White.

The Tri-Spin Base and Rib Structure

•       Rib structure: Twenty raised internal ribs support the filter paper and hold its shape through the brew.

•       Tri-Spin hollowed base: Spreads the outflow across the base instead of concentrating it in the center, which reduces clogging at larger doses.

•       New bone china body: Heat resistant to 120°C (248°F). Safe for dishwashers, microwave ovens, and dish dryers.

What's in the Box

•       Dripper: DragonFly Tri-Spin FS Flat Dripper (280ml) x 1

Specifications

A 255ml bone china flat-bottom dripper for 1 to 2 servings, made to sit on a transit base for switch-controlled brewing or a bamboo holder for a standard pour over

The Tri-Spin CT Flat Dripper from DragonFly Design Center is a new bone china flat-bottom pour over dripper built to close that gap. It starts from the CT62 conical dripper and rebuilds it around a flat bottom, with a grooved inner wall and DragonFly's Tri-Spin base.

How the Tri-Spin CT Manages Flow

The inner wall is a flat surface cut with 12 long grooves and 12 short grooves. The filter paper adheres to a larger area of the wall, so there is less room for water to bypass the bed and more of each pour passes through the grounds.

The grooves act as flow guides and pressure relief channels, which keeps the drawdown smooth and the extraction even across the bed. The result is a even extracted cup with clear layers of sensory expression.

At the base, the Tri-Spin hollowed design with multiple grooves spreads the water's exit points to avoid concentration in the center. This reduces the risk of the clogging and helps water move through the whole bed. This matters even more with larger doses, where localized over-extraction is more likely.

DragonFly developed the CT Flat with competition brewing in mind, where a stable, repeatable extraction counts for more than speed.

The Shanwen Jia Exterior

The outer wall carries the Shanwen Jia (山文甲) pattern first used on the CT62. Shanwen Jia, also known as Shanwen Armor, is a Tang Dynasty armor recognized by its repeating mountain pattern. On the dripper, that pattern wraps the outer wall as a continuous geometric repeat.

The exterior is the link between the two brewers. The CT62 pairs it with a conical interior, and the Tri-Spin CT pairs it with a flat bed and a grooved wall.

Product Details

Brewing with the Transit Base or Bamboo Flat Dripper Holder (Purchase separately)

Paired with the DragonFly Flat-Bottom Transit Base, the dripper brews two ways. With the transit knob open, it runs as a flat-bottom pour over and gives a clean, filter-style cup. With the switch closed gives a fuller, immersion-style cup.

You can also choose to brew with a Bamboo Flat Dripper Holder – using it as a traditional pourover dripper.

It holds 255ml, brews 1 to 2 servings, and takes foldable flat-bottom filter paper or 185 flat-bottom paper filters.

The Groove Structure and Tri-Spin Base

•       Groove structure: Twelve long and twelve short grooves on a flat inner wall let the filter sit closer to the wall while still guiding flow and relieving pressure.

•       Tri-Spin hollowed base: Disperses the outflow instead of concentrating it in the center, which reduces clogging at larger doses.

•       New bone china body: Heat resistant to 120°C (248°F). Safe for dishwashers, microwave ovens, and dish dryers.

What's in the Box

•       Dripper: DragonFly Tri-Spin CT Flat Dripper (255ml) x 1

Specifications

A 62-degree conical dripper with a built-in stand that sits on your carafe and keeps the flow even from bloom to drawdown

The DragonFly CT62 from DragonFly Design Center is a new bone china conical dripper with a 62-degree interior angle, built to hold the filter close and keep the flow even, available in Grey, Black, and White. Its built-in stand rests on the rim of a carafe or serving vessel, so it brews straight into your server on its own.

How the DragonFly CT62 Manages Flow

The interior is an original DragonFly Design Center design, refined through repeated brewing tests to reach a uniform flow rate. The goal is a balanced drawdown, which helps prevent clogging and over-extraction and preserves the coffee's aroma and flavor.

The cone is set at 62 degrees so the filter paper sits snugly against the inner wall. With the paper in steady contact, water percolates through the bed at a repeatable rate from one brew to the next, keeping extraction consistent.

The Shanwen Armor Exterior (山文甲)

The CT in the DragonFly CT62 refers to its exterior texture, based on Shanwen armor (山文甲) from China's Tang Dynasty. The 62 refers to the interior cone angle.

The Shanwen design is an original concept from medieval China that takes a flat pattern and builds it directly into a three-dimensional form. DragonFly Design Center brought that approach to the dripper as a contemporary geometric exterior: curved surfaces and facets cover the full body, and the geometry repeats across it, giving the surface depth and perspective from any angle.

The built-in stand follows the same Shanwen Jia pattern, with one corner extended to form the handle, so the dripper and stand carry one visual language.

Product Details

Brewing with the Built-In Stand

The built-in stand sits on the rim of a carafe or serving vessel and holds the dripper securely in place while you pour. Three curved sections at its center surround the bottom of the dripper to keep it from slipping.

One corner of the stand extends into a handle. It rises slightly at the tip and has concave and convex details on the top and underside, giving a secure three-finger grip when you set the dripper on the carafe or lift it off after drawdown.

The DragonFly CT62 brews 1 to 2 servings and takes V60 size 01 and 02 conical paper filters.

The 62-Degree Cone and Body

•     62-degree cone: Holds the filter paper snugly against the inner wall for consistent extraction.

•     Flow-tested interior: Refined through repeated brewing tests for a uniform flow rate and less clogging.

•     New bone china body: Heat resistant to 120°C (248°F). Safe for dishwashers, microwave ovens, and dish dryers.

What's in the Box

•     Dripper: DragonFly CT62 with built-in stand x 1

Specifications

A 62° conical dripper sized for 1- 4 cup, with an internal groove structure that keeps the drawdown steady at larger doses

The CT62 Dripper 02 (390ml) from DragonFly Design Center is a new bone china conical dripper made for a larger, 1-4 cup brew. It carries the 62° angle, internal grooves, and exterior texture of the original CT62, with a taller body that raises capacity from 1 to 2 servings to 1 to 4. It is available in Black and White.

How the CT62 Manages Flow

The cone is set at 62°, a proprietary angle DragonFly developed to give a broad, stable extraction range. It responds well to a centered pour or a wider circular spiral pour, so you can adjust your technique without the brew losing balance.

Inside, 24 grooves guide water down the wall. Instead of the raised ribs found in many conical drippers, the CT62 uses recessed channels, with an added ring of horizontal grooves near the base to regulate flow through the lower part of the cone.

DragonFly refined this channel design through repeated testing. The goal is a drawdown that holds a consistent pace from start to finish, which helps reduce clogging and the bitterness, astringency, and sourness that come with uneven extraction.

Product Details

Compatible with the DragonFly Design Center Conical Dripper Transit Base

Set the DragonFly Design Center CT62 Transit Pro Dripper 02 (390ml) and you have instantly transformed it to a hybrid brewer with variable flow rate.

Brewing with the CT62 02

The dripper sits over a cup or server for standard pour over brewing. At 390ml, it handles 1 to 4 servings, so the same brewer works for a single morning cup or a shared pot. It takes 1-4 cup paper filters.

Its base has an integrated raised ring that seats into the DragonFly Conical Dripper Transit Base. It also pairs with the DragonFly Conical Dripper Holder and Silicone Ring for a more secure, stable setup on the brew table.

The new bone china body is heat resistant to 120°C (248°F) and safe for dishwashers, microwave ovens, and dish dryers.

The 62° Cone and Groove Structure

•     62° conical geometry: A proprietary angle that gives a wide working range and room to vary pour style.

•     24 recessed channels: Guide water downward along the wall in place of raised ribs, for a steadier drawdown.

•     Horizontal groove ring: Sits near the base and regulates flow through the lower cone as the bed settles.

The Shanwen Armor Exterior

The CT in the DragonFly CT62 refers to its exterior texture, based on Shanwen armor (Shanwen Jia) from China's Tang Dynasty. The 62 refers to the interior cone angle.

The Shanwen design is an original concept from medieval China that takes a flat pattern and builds it directly into a three-dimensional form. DragonFly Design Center brought that approach to the dripper as a contemporary geometric exterior: curved surfaces and facets cover the full body, and the geometry repeats across it, giving the surface depth and perspective from any angle.

The built-in stand follows the same Shanwen Jia pattern, with one corner extended to form the handle, so the dripper and stand carry one visual language.

What's in the Box

•     Dripper: DragonFly CT62 Dripper 02 (390ml) x 1

Specifications

A knob-controlled base for the DragonFly CT62 Transit Pro Dripper, letting it hold water for immersion or release it for drawdown

The Conical Dripper Transit Base from DragonFly Design Center is a knob-controlled base built for the DragonFly CT62 Transit Pro Dripper, available with a Black, White, Pink, or Purple knob. Turn the knob closed and the conical dripper becomes a full immersion brewer, holding the slurry for as long as your recipe calls for. Open it and the brew drains through the filter as a standard percolation pour over.

Setting the knob partway lets you meter the flow rate, so you can slow the drawdown without changing your grind size.

How the Transit Base Controls Flow

With the knob turned closed, water stays in contact with the grounds and extraction runs as immersion. Contact time is set by you, not by grind size and filter resistance. Turn the knob open and drawdown begins, finishing the brew as percolation, with water moving through the bed and the paper filter holding back fines and oils.

This makes hybrid recipes possible in a single brewer: a closed bloom for even saturation and degassing, an immersion phase to build body and extraction, then an open percolation finish for clarity. You can adjust the timing and balance of each phase on the fly, with no change to the dripper, filter, or grind.

The base comes apart in two sections joined by a magnetic connection, so it separates cleanly for rinsing and snaps back together for the next brew. Three feet keep it level on the server.

Product Details

Brewing with the Transit Base

Set the CT62 Transit Pro Dripper on the base, place it over your server, and choose your starting configuration. With the knob closed, you control contact time directly. A closed bloom saturates the whole bed before any liquid drains, which reduces dry pockets and channeling and sets a foundation for even extraction.

With the knob open, the dripper behaves like a conventional conical pour over, and pour rate, pulse timing, and agitation drive the extraction.

The CT62 Transit Pro Dripper takes Size 02 conical paper filters.

The Knob and Base Construction

•     Knob control: A single knob opens and closes the flow path, moving between immersion and percolation mid-brew, with partial settings to adjust flow rate.

•     Magnetic two-part base: The upper and lower sections join magnetically and detach for assembly and cleaning.

•     Three-foot stand: A compact, three-foot footprint keeps the dripper stable over the server.

What's in the Box

•     Transit Base: DragonFly Conical Dripper Transit Base x 1

Specifications

The Switch and Base Construction

•     Knob control: A single knob opens and closes the flow path, switching between immersion and drawdown mid-brew.

•     Magnetic two-part base: The upper and lower sections join magnetically and detach for assembly and cleaning.

•     Three-foot stand: A compact, three-foot footprint keeps the dripper stable over the server.

What's in the Box

•     Transit Base: DragonFly Conical Dripper Transit Base x 1

Specifications