DragonFly Tri-Spin FS Flat Bottom Dripper - 280ml
Regular price $55.75 Save $-55.75A flat-bottom pour over drains evenly when the coffee bed stays level and water can exit across the whole base. Uneven flow usually starts where the filter meets the brewer: the paper folds against the wall, fines collect in the center, and the middle of the bed slows while the edges drain through.
The Tri-Spin FS Flat Dripper from DragonFly Design Center, also known by its Chinese name 三旋空玄武 (Xuanwu), is a new bone china flat-bottom brewer designed to keep that flow even. Its transit base lets you brew as a standard pour over, or close the knob and steep as an immersion.
Inside the dripper, 20 raised ribs hold the filter paper off the wall so it keeps its shape through the brew. With the paper supported, water moves through the bed at a more consistent rate, and results vary less from one brew to the next.
The wall angle is set to keep the flow rate quick while still allowing a finer grind. A finer grind raises extraction yield, so a faster drawdown can still reach a full extraction and keep a clear, layered flavor.
At the base, DragonFly's Tri-Spin hollowed design spreads the water's exit points across the base rather than concentrating them in the center. This reduces clogging and keeps water moving through the whole bed instead of stalling in the middle, which matters most at larger doses where localized over-extraction is more likely.

The dripper received a German Design Award in 2026.
The outer wall carries the Shanwen Jia (山文甲) pattern first used on the CT62. Shanwen Jia, also known as Shanwen Armor, is a Tang Dynasty armor recognized by its repeating mountain pattern. On the dripper, that pattern wraps the outer wall as a continuous geometric repeat.
The exterior is the link between the two brewers. The CT62 pairs it with a conical interior, and the Tri-Spin CT pairs it with a flat bed and a grooved wall.

With the Transit Base open, it brews as a fast-flowing flat-bottom pour over and gives a clean, filter-style cup. With the switch closed, water stays in contact with the grounds until you open it, which gives a fuller, immersion-style cup.
Immersion is a forgiving starting point while your pour technique is still developing. The open setting gives experienced brewers direct control over pour rhythm and timing.

You can also choose to brew with a Bamboo Dripper Holder – using it as a traditional pourover dripper.
DragonFly Tri-Spin FS Flat Bottom Dripper - 280ml brews 1 to 2 servings, and takes 185 flat-bottom paper filters. It is available in Shell Pink, Black, and White.
• Rib structure: Twenty raised internal ribs support the filter paper and hold its shape through the brew.
• Tri-Spin hollowed base: Spreads the outflow across the base instead of concentrating it in the center, which reduces clogging at larger doses.
• New bone china body: Heat resistant to 120°C (248°F). Safe for dishwashers, microwave ovens, and dish dryers.
• Dripper: DragonFly Tri-Spin FS Flat Dripper (280ml) x 1
|
Brand |
DragonFly Design Center |
|
Product Name |
Tri-Spin FS Flat Dripper (280ml) |
|
Weight |
210g net (340g gross, packaged) |
|
Dimensions |
104mm top diameter x 60mm bottom diameter x 77mm height |
|
Material |
New bone china |
|
Care |
Dishwasher safe. Also safe in microwave ovens and dish dryers. |
|
Origin |
China |
|
Capacity |
280ml, 1 to 2 servings |
|
Filter |
185 flat-bottom paper filter |
|
Heat Resistance |
Up to 120°C (248°F) |
|
Award |
German Design Award 2026 |
|
Color |
Shell Pink, Black, White |
Colors of actual products might show up slightly different than in the product photos. This is due to the various settings of monitors. Every monitor or mobile display has a different capability to display colors, and every individual may see these colors differently. In addition, lighting conditions at the time the photo was taken can also affect an image's color.
Products that have a shimmering coating will also show differently under different lighting setup. Colors might appear different even under a fluorescent light or a warmer shade bulb.
ORIGAMI Ceramic Dripper - Medium for 1-4 Cup Brewing
Regular price $40.75 Save $-40.75The ORIGAMI Dripper Medium is sized for 1-4 cup brewing, for a brew prepared for sharing or at cafés preparing larger brews up to 40 grams dosage.
Handcrafted in Toki City, Gifu Prefecture, the ceramic heartland of Japan, the ORIGAMI Small Ceramic Dripper carries the same Mino-yaki porcelain tradition as its larger counterpart: a craft four to five hundred years old, practiced today by only a few dozen artisans. In your hands it is a brewer. In theirs it is a continuation of something much older.
The 20-fold interior works with both conical and wave style filters, giving you the freedom to brew to the cup you want, not the equipment you have. Conical filters encourage faster airflow and a brighter extraction. Wave filters settle the flow, producing something fuller and rounder. The porcelain holds heat steadily through both.
Mino-yaki is the ceramic tradition of the Toki area in Gifu Prefecture, a region long celebrated in Japan for its pottery and washi paper. The techniques used to produce ORIGAMI Drippers are the same ones that have shaped ceramics in this region for generations, refined over centuries and carried forward by the artisans who remain.
The ORIGAMI Dripper was designed by the founder of Trunk Coffee in collaboration with these makers. The result is a brewer shaped by both the culture it comes from and the demands of specialty coffee. It has been used by World Brewers Cup competitors and sits equally well on a competition table or a kitchen counter.
The 20-fold interior of the ORIGAMI Dripper Medium does two things well. With a conical filter, the folds create airflow channels between the filter and the dripper wall, encouraging faster, more even extraction. With a wave filter, the flat bed geometry changes the brew dynamic entirely, slowing flow rate and producing a fuller, rounder cup. One dripper, two distinct approaches.
The high-density Mino porcelain retains heat through the full pour, keeping the brew bed temperature stable from bloom to drawdown.
A dripper collar or holder is strongly recommended to stabilize the ORIGAMI Dripper during brewing and prevent it from sitting directly in the server. The ORIGAMI Wooden Holder and ORIGAMI AS Resin Holder are both available separately and sized for this dripper.
The ORIGAMI Dripper Medium is compatible with the following filter papers. The ORIGAMI Dripper Medium is compatible with the following filter papers. ORIGAMI also manufactures its own ORIGAMI Wave (Flat Bottom) Filter Box.
Conical ORIGAMI Conical Filter (Cup 4), Sibarist Cone M, HIFLUX Coffee Filter - Cone Folding V 50 Sheets
Hybrid Sibarist B3 Hybrid Filter
Wave Origami Wave Medium, April Large Wave Filter, Hiflux Wave Filter 185, Kalita Wave 185,
We recommend to not only stick with one style of filter, but to try out different filters for your recipes.
This listing is for one ORIGAMI Dripper Medium (dripper only). Available in a wide range of colours. A dripper holder is not included and is purchased separately.
– ORIGAMI Dripper Medium x 1
Check out our 2023 ORIGAMI brew recipes to follow along! This collection of recipes by coffee roasters across the nation features coffees from different region and processing methods. Happy brewing!
Made of Mino porcelain, the ORIGAMI dripper is a product that represents 400 years of rich history in high quality ceramicware produced in the Toki area of Gifu prefecture. These colorful and eye-catching drippers are popular among Brewing Championship competitors.
– Brand ORIGAMI Japan
– Weight approx. 200g (M) , 135g (S)
– Dimensions (Medium) 138mm (W) x 87mm (H), drip hole: 25mm (M), (Small) 115mm (W),70 mm (H), drip hole: 25mm
– Brew Capacity 1 to 4 cups (M), 1 to 2 cups (S)
– Material Mino-yaki porcelain (high-density Mino clay, Gifu Prefecture, Japan)
– Available Colours Multiple colourways available. Refer to listing for current options.
– Compatible Filters (Medium) ORIGAMI Conical Filter Cup 4, Hiflux Folding V (M), Hario V60 02, Sibarist Cone M, Sibarist Hybrid, CAFEC Cup 4, Kalita Wave 185
(Small) ORIGAMI Conical Filter Cup 2, Hiflux Folding V (S), Hario V60 01, Sibarist Cone S, Sibarist Hybrid, CAFEC Cup 2, Kalita Wave 155
– Compatible Holders ORIGAMI Wooden Holder, ORIGAMI AS Resin Holder (sold separately)
– Care Hand washing recommended. Microwave, oven, and dishwasher safe.
– Origin Made in Mino, Gifu Prefecture, Japan

| Item | Price | Qty | Total | |
|---|---|---|---|---|
| Subtotal |
$0.00 |
|||
| Shipping | ||||
| Total | ||||