Custom Discount Collection

The UFO Ceramic Dripper is compatible with a wide range of filters. Please make your selection to find your fit!

UFO Variable Wall Thickness Technology, and the reason behind the decision to not include base (holder).

Ceramic UFO is an attempt at stabilizing coffee slurry temperature throughout brewing. Via reducing unnecessary thermal mass from the upper levels of the dripper construction and positioning the dripper as close as possible to the heat retained within the carafe by removing the base, the ceramic UFO is able to create a brewing process that draws from a more stable incubated heat from below the brewer throughout the brewing process. 

Ceramic UFO’s uppermost wall thickness is 23.7% thinner than the lowermost wall thickness, removing unnecessary thermal mass.

Ceramic UFO is designed to sit directly on the server, which allows the hot heat from the output coffee inside the server to circulate upwards, constantly providing an additional source of heat towards the thickest part of the dripper for better thermal stability.

This would be an issue in traditional protruding-rib designs where airflow is heavily dependent on the separation of the dripper base and server via base risers, but with UFO’s air channels that provide constant and consistent air flow from behind the filter, fear of clogging (stalling) via air-lock is fully out of question.

Filters Compatibility

Compatible with variety of filters.

UFO Type A, Sibarist UFO Special Edition, Sibarist UFO B3 Flat 

Most drippers manage heat from the outside in. The UFO Ceramic Dripper approaches it differently, pulling warmth upward from the server below and concentrating it where the coffee needs it most. The result is a more stable brew bed temperature from start to finish, without adding complexity to your pour.

The UFO is designed to sit directly on your server. That contact point is intentional: hot air rising from the output coffee inside the server circulates upward into the thickest, most thermally active section of the dripper wall, supplementing the heat the ceramic itself retains. It is a passive system, and it works precisely because of where the dripper sits, not despite it.

The Design Rationale

Variable wall thickness is the core of what makes the UFO work. The uppermost wall is 23.7% thinner than the lowermost wall. This reduction removes thermal mass from the top of the dripper, where it would have little useful effect, and concentrates it at the base, closest to the heat source below. Thicker walls at the bottom retain more heat. Thinner walls at the top stay out of the way.

Conventional drippers that use protruding rib designs rely on separation between the dripper base and the server, typically via base risers, to maintain airflow. That separation, while necessary for airflow, also cuts off the dripper from any heat the server provides. The UFO resolves this with internal air channels that deliver consistent airflow from behind the filter without requiring the dripper to be lifted away from the server. Airlock and stalling are not concerns.

Product Details

The Setup

The UFO Ceramic Dripper sits directly on your server, carafe, or cup without a separate holder. This is a deliberate design choice, not an omission. Removing the base keeps the dripper in direct thermal contact with the vessel below, enabling the upward heat circulation the design depends on. A holder would interrupt that connection.

Compatible Filters

The UFO Ceramic Dripper is compatible with the following filters:

•       UFO Type A Filter (available separately)

•       Sibarist UFO Special Edition Fast Cone (available separately)

•       Sibarist UFO B3 Flat (available separately)

Trying different filters is the best way to explore what this dripper can do. Each one changes the flow dynamic in a way that is worth experiencing.

What's in the Box

•       UFO Ceramic Dripper  x 1

The 2026 World Brewers Cup Champion Nas Jaafar (representing Malaysia) brewer of choice.

The UFO Dripper  V3 is a standalone dripper that can be adapted to the "Hario Switch" brewing system.

Geometry That Guides Extraction

At the core of the V3 is an 80° interior angle designed to promote steady drawdown while maintaining even bed saturation. This angle supports efficient flow through the coffee bed, helping reduce channeling and minimizing stall. Rather than relying on aggressive flow restriction or mechanical intervention, the structure itself regulates movement and extraction.

This geometry also improves performance across a wider grind spectrum - extraction remains controlled and predictable, allowing grind size and pour adjustments to translate clearly into the cup.

Profiles remain expressive yet structured.

Negative Channels and Flow Stability

The negative channel design supports balanced airflow during drawdown, preventing vacuum lock and reducing turbulence. By stabilizing the brew bed and minimizing uneven water distribution, the V3 maintains clarity and a controlled flow.

The result is faster, consistent drawdown without sacrificing balance.

Expanded Capacity for Recipe Flexibility

The larger brew chamber increases practical flexibility. It accommodates higher doses and a broader range of brew ratios while offering greater tolerance for controlled agitation. This enables movement between lighter, clarity-focused brews and fuller extractions without destabilizing the bed.

Designed for Hybrid Brewing

The V3 functions as a standalone percolation dripper with stable flow characteristics. It is equally engineered for adaptation. When paired with the Hario Switch base, it becomes a hybrid immersion system.

In this configuration, you can extend contact time, hold water before release, and intentionally increase extraction depth. The same geometry that supports clean percolation also ensures controlled immersion drawdown once the valve is opened.

One brewer with two distinct extraction approaches. The 80 degree UFO Dripper V3 delivers structural clarity, adaptable workflow, and repeatable results without unnecessary complexity.

Material: Food Safe Triton Resin

Weight: 250g approx

For up to 4 cup brewing.

As per supplier request, the new price for all Sibarist products have been adjusted on 10.1.26

The UFO Special editions are the filters that perform the maximum potential, yield and fitting of the UFO dripper.

The UFO B3 Flat works for UFO V2. For V3, please use the UFO Type F filters.

The filters ensure the no bypass but let extraction be driven through the UFO original air channels design, achieving an special and stunning cup profile.

The UFO dripper is a Jay and Kenzie development, they based all the R&D to create the UFO around the Sibarist filters due the performs consistently every single time. The UFO special edition goal is to share the utmost consistent brewing experience with the brewing community.

UFO: “We wanted to create a conical dripper that can not only capture clarity and complexity, which are characteristics of a traditional 60-degree wall angle conical dripper but also sweetness and even extraction of a flat bottom dripper, leading to cups with incredible clarity and intensity. Once we achieved that through UFO’s unique 80-degree wall angle, our next mission was to solve the consistency issue of a conical dripper. That’s when we designed our UFO air channels alongside UFO blocks that the filters sit on with enough surface tension to not collapse into the air channels. The result is something truly special, a cup profile that has never existed before. One that combines the best of the flat bottom and the conical geometry. We cannot wait for you all to experience it soon.”

 There are two filter paper technologies available for the UFO dripper:

• The B3 Specialty Coffee Filters (The filter is delivered unfolded, se HOW TO USE below)

“B3 flows slower than FAST. We enjoy B3 for fast flowing process impact-heavy (natural/anaerobic natural/carbonic maceration/co-ferment/yeast-inoculated, etc) coffees that require coarser grind sizes and a slower flow rate to provide sufficient contact time to extract all the good things while avoiding over extraction of the mega funky flavours that can often be overwhelming. This can also apply in roast levels. The more developed the roast, the more we will lean towards the B3 and grind even coarser.”

Designed specifically for the UFO Dripper ecosystem, the Type A is a medium-flow paper filter engineered for balanced extraction and cup clarity.

The Type A regulates drawdown to support even water movement through the coffee bed, allowing for consistent extraction without rushing or stalling. This controlled flow helps preserve sweetness and structure while minimizing the risk of over-extraction across a wide range of coffees.

The filter geometry works in harmony with the UFO Dripper’s unique 80-degree form, promoting even saturation and consistent drawdown from bloom to finish. When paired with a slightly coarser grind and steady pours, the result is a clean, articulate cup that highlights origin character and balance.

Whether you’re dialing in a daily brew or refining a competition routine, the UFO Type A paper filter is built to support precision and repeatability in your pour-over process.

Introducing the UFO Dripper — Type F 01 Filters for 01 size UFO Brewer

Built for brewers who want speed without compromise.

The Type F 01 filter is designed for UFO V3 01 or UFO Ceramic Dripper to flow fast while maintaining balance and control, giving you the freedom to push extraction without sacrificing clarity or structure in the cup.

Produced with 100% FDA-approved lyocell and PLA, Type F filters are engineered as a true fast-flow option within the UFO ecosystem. The material composition creates a strong yet open filter structure that supports quick drawdown while staying stable throughout the brew.

What sets Type F 01 apart is how it handles water movement. The faster flow allows you to:

• Brew efficiently without choking
  

• Explore finer grind sizes with confidence
  

• Maintain sweetness and balance, even at higher extractions
  
  

The result is a cup that feels clean, controlled, and expressive; highlighting origin character while keeping the mouthfeel intact.

Whether you’re dialing in light roasts, refining your competition recipes, or simply looking for a more efficient daily brew, Type F offers speed with intention.

Comptable with:
UFO V3 01, UFO Ceramic, UFO V2

Introducing the UFO Dripper — Type F Filters

Built for brewers who want speed without compromise.

The Type F filter is designed to flow fast while maintaining balance and control, giving you the freedom to push extraction without sacrificing clarity or structure in the cup.

Produced with 100% FDA-approved lyocell and PLA, Type F filters are engineered as a true fast-flow option within the UFO ecosystem. The material composition creates a strong yet open filter structure that supports quick drawdown while staying stable throughout the brew.

What sets Type F apart is how it handles water movement. The faster flow allows you to:

• Brew efficiently without choking
  

• Explore finer grind sizes with confidence
  

• Maintain sweetness and balance, even at higher extractions
  
  

The result is a cup that feels clean, controlled, and expressive; highlighting origin character while keeping the mouthfeel intact.

Whether you’re dialing in light roasts, refining your competition recipes, or simply looking for a more efficient daily brew, Type F offers speed with intention.

Designed to improve the quality of your espresso shots the WPM WDT tool gently stirs the coffee grounds before tamping.

 By breaking up clumps and minimizing channeling, it ensures an even distribution of grounds, leading to a more consistent and flavorful extraction with every brew.

Promote even extraction for your pourover by breaking up crumbs and redistribute unevenly dosed pourover grinds. Gently stir after dose to promote an even brew bed.

The needle is equipped with a convenient side magnet, allowing it to be easily stored on the metallic body of your espresso machine or any cabinets. This thoughtful feature ensures that the tool is always within reach and ready for use.

As per supplier request, the new price for all Sibarist products have been adjusted on 10.1.26

The World Aeropress Championships all-in-pack is an exclusive limited-edition pack including tools of designed to inspire you to explore, experiment, and cradt unique recipes for the perfect extraction. 

Each filter and accessory offers distinct filtration qualities, unlocking endless ways to elevate your Aeropress brew!

This pack includes:

1. 30 x Sibarist Fast Disc 63
2. 30 x Sibarist B3 Disc 63
3. 1 x Sibarist Booster
4. 30 x Sibarist High Cellular Disc 63

The WPM 10oz and 22oz WPM Barista Bundle in Cinder pairs two of WPM's most trusted pitcher sizes in a single matte gray finish with a warm red undertone. Baristas get a small pitcher built for precise, low-volume pours and a large pitcher built for bold service and to-go pours, both finished to match for a consistent look on the bar.

This bundle is designed for baristas and cafes that need one pitcher for delicate small-cup latte art and another for higher-volume service, without mixing finishes or replacing an entire pitcher set piece by piece.

WHY YOU'LL LOVE IT

–      Two pitcher sizes in one matching Cinder finish, so small-cup and large-cup service share a consistent look.

–      10oz Model #26 pitcher with a medium-wide spout balances flow and control for cups under 6oz.

–      22oz Model #09 pitcher with a wide spout delivers a bold, high-flow stream for large to-go cups and milk sharing.

–      Signature WPM slanted top on both pitchers brings the milk stream closer to the crema for easier pour starts.

–      9.5oz milk volume indicator on the 22oz pitcher helps gauge steamed milk levels before pouring.

–      Wide diameter vessels on both sizes give steaming milk more room to move for smoother microfoam.

–      304 (18/8) stainless steel construction with an uncoated, food-safe interior on both pitchers.

RECOMMENDED FOR

–      Cortados, small cappuccinos, and gibraltars using the 10oz pitcher.

–      Large to-go cups and higher-volume service pours using the 22oz pitcher.

–      Milk sharing between two pitchers of matching size and finish.

–      Cafes and home baristas who want one finish across both small and large pours.

DESIGN PHILOSOPHY

WPM builds its pitcher line around matching a proven body and spout profile to a specific pour volume, rather than scaling one design across every size. The Cinder bundle applies that approach across two sizes at once, giving baristas a small pitcher tuned for controlled, low-volume pours and a large pitcher tuned for higher flow, both finished in the same ash gray coating with a red hue.

Pairing the 10oz and 22oz pitchers together also supports a common café workflow: the smaller pitcher for individual small-cup orders and the larger pitcher for shared or to-go volumes, without switching between mismatched finishes during service.

DESIGN FEATURES

10OZ MEDIUM-WIDE SPOUT, MODEL #26

The 10oz pitcher uses a medium-wide spout that balances flow and control at small volumes. It is sized for cups under 6oz, including cortados, small cappuccinos, and gibraltars, where controlled placement matters more than pour speed.

22OZ WIDE SPOUT, MODEL #09

The 22oz pitcher uses a round, wide spout suited to bold, dramatic pours. It is built for larger to-go cups and for milk sharing, where a higher flow rate speeds up service without sacrificing pour control.

SIGNATURE WPM SLANTED TOP

Both pitchers use WPM's signature slanted top, which angles the milk stream toward the crema surface sooner. This reduces the tilt needed to start a pour and applies to both the 10oz and 22oz pitchers in this bundle.

MILK VOLUME INDICATOR

The 22oz pitcher includes a 9.5oz milk volume indicator built into the slanted top, giving baristas a visual reference for steamed milk levels before pouring or sharing between pitchers.

WIDE DIAMETER VESSEL

Both pitchers use a wide body diameter relative to their capacity. This gives steaming milk more room to move during texturing, supporting smoother microfoam in both the small and large pitcher.

FULL HANDLE

Both pitchers include a full loop handle sized to accommodate a range of grip styles, keeping the pour stable from initial tilt through finishing lines.

MATTE CINDER FINISH

The Cinder finish is a matte gray powder coating with a subtle red hue over the exterior of both pitchers. The interior on both sizes is left uncoated, keeping it food safe and easy to clean after each use.

The name Cinder, an ash gray finish with a red hue, is credited to Morgan Eckroth.

PERFORMANCE

RECOMMENDED DRINK SIZES

The 10oz pitcher is sized for cups under 6oz, including cortados, small cappuccinos, and gibraltars. The 22oz pitcher is sized for larger to-go cups and for milk sharing between service pours.

POURING CHARACTERISTICS

The 10oz pitcher's medium-wide spout produces a balanced flow suited to controlled placement at small volumes. The 22oz pitcher's wide spout produces a higher flow rate for bold, dramatic pours at larger volumes.

WORKFLOW

Keeping both sizes in the same Cinder finish lets baristas move between small-cup orders and larger to-go or shared pours without switching pitchers of different colors during service. The 22oz pitcher's milk volume indicator also makes it easier to divide milk between the two pitchers when sharing.

SPECIFICATIONS

10OZ PITCHER, MODEL #26

22OZ PITCHER, MODEL #09

WHAT'S INCLUDED

–      1 x 10oz WPM Latte Art Pitcher, Model #26, in Cinder.

–      1 x 22oz WPM Latte Art Pitcher, Model #09, in Cinder.

CARE & MAINTENANCE

Hand wash both pitchers with warm water and a mild detergent after each use, focusing on the interior where milk residue collects. Dry each pitcher immediately with a soft cloth to keep the Cinder finish free of water spots. Avoid abrasive pads, harsh chemicals, or prolonged soaking, since milk's acidity can wear down stainless steel's protective layer over time if residue is left to sit.

FREQUENTLY ASKED QUESTIONS

WHAT COMES IN THIS BUNDLE?

The bundle includes one 10oz pitcher (Model #26) and one 22oz pitcher (Model #09), both finished in matching Cinder.

WHAT IS THE CINDER FINISH?

Cinder is a matte gray powder coating with a subtle red hue, applied to the exterior of both pitchers. The interior on both sizes remains uncoated stainless steel.

WHAT DRINK SIZES ARE EACH PITCHER DESIGNED FOR?

The 10oz pitcher is designed for cups under 6oz, such as cortados, small cappuccinos, and gibraltars. The 22oz pitcher is designed for larger to-go cups and milk sharing.

WHY PAIR A 10OZ AND 22OZ PITCHER TOGETHER?

Pairing the two sizes lets a barista use the small pitcher for individual small-cup pours and the large pitcher for shared or higher-volume pours, both in the same finish.

HOW SHOULD I CLEAN AND MAINTAIN THE FINISH?

Hand wash both pitchers with warm water and mild detergent, then dry immediately with a soft cloth. Avoid abrasive pads and prolonged soaking to protect the interior stainless steel and the Cinder exterior on both pitchers.

The 10oz and 22oz WPM Barista Bundle in Cinder gives baristas a matched pair of pitchers for both delicate small-cup latte art and higher-volume service pours. Between the medium-wide spout on the 10oz pitcher and the wide spout on the 22oz pitcher, the bundle covers a full range of everyday café pours in one consistent finish.

The WPM 10oz Latte Art Pitcher with Narrow Spout in Matte Black is built for small format espresso drinks that call for precise pour placement. Its narrow #07 spout slows the flow rate just enough to give baristas fine control when working in cups under 6oz. The matte black finish and wide-diameter body make it equally suited to daily service and focused practice sessions.

Why you'll love it

- Narrow #07 spout profile reduces flow rate for precise placement in small cups.

- WPM's signature slanted top design directs milk to a single exit point for consistent pours.

- Wide-diameter body holds a full 10oz for proper steaming without volume constraints.

- Full loop handle accommodates multiple grip positions during the pour.

- Matte black powder coated exterior resists visible wear during regular use.

- Uncoated 304 18/8 stainless steel interior keeps the pitcher food safe and easy to clean.

Recommended for

- Macchiatos, cortados, and piccolo lattes served under 6oz.

- Baristas learning controlled pour placement on small format drinks.

- Fine line latte art patterns that depend on a steady, focused stream.

- Cafe service where consistency across small drinks matters.

Design philosophy

WPM designed the Model #27, known as the Small Blankenburg, specifically for milk drinks under 6oz. Rather than scaling down a larger pitcher, WPM paired a 10oz body with its narrow #07 spout so the flow rate matches the smaller pour target. This keeps the milk stream controlled instead of overwhelming a small cup.

The wide-diameter shape preserves enough interior volume for proper steaming even at this smaller capacity. Combined with WPM's slanted top, the result is a pitcher built around the specific demands of small format espresso drinks rather than a general-purpose design shrunk to fit.

Design features

WPM #07 narrow spout

The #07 spout has a narrow, lipped profile that reduces flow rate at the pour point. This gives baristas more time to react and adjust placement, which matters most when working with the limited surface area of a cup under 6oz.

Signature slanted top

WPM's slanted top design angles the pour edge instead of using a flat rim, directing the milk stream to a single exit point. This produces a more consistent stream shape from pour to pour, which supports repeatable pattern work.

Wide-diameter body

The body is wide relative to its 10oz capacity, which gives the pitcher enough interior room to steam properly without being constrained by a taller, narrower shape. This helps maintain steaming consistency even at the smaller volume.

Full loop handle

The full loop handle is sized to accommodate different grip positions, letting baristas adjust their hold as needed without losing control of the pour.

Performance

Pouring characteristics

The narrow #07 spout reduces flow rate compared to a wide or round spout, giving the barista more control over exactly where the milk lands. This makes it easier to build fine lines and maintain clean pattern edges.

Recommended drink sizes

The 10oz (300ml) capacity is sized for drinks under 6oz, including macchiatos, cortados, and piccolo lattes. At this size, the reduced flow rate of the narrow spout suits smaller volumes where placement accuracy matters more than pour speed.

Suitable patterns

The controlled, focused flow works well for ripple hearts, traditional rosettas, wing base tulips, hanging hearts, and swans. The steady stream also makes pour placement approachable for beginners while still supporting the precision needed as skill develops.

Specifications

What's included

- 1 x WPM 10oz Latte Art Pitcher with Narrow Spout in Black.

Care & maintenance

Hand wash with warm water and mild soap after each use, paying close attention to the interior where milk residue builds up. Dry the pitcher fully with a towel and store it right side up to prevent water spots. Avoid prolonged exposure to acidic milk residue, since this can wear down the protective layer on stainless steel over time.

Frequently asked questions

What cup sizes is this pitcher designed for?

It is designed for drinks under 6oz, including macchiatos, cortados, and piccolo lattes.

Why does the narrow spout matter at this size?

The narrow #07 spout reduces flow rate, giving more precise control over pour placement in a smaller cup than a wide or round spout would allow.

Is this pitcher suitable for beginners?

Yes. The steady, focused flow makes pour placement easier to learn, and it continues to support precision as pouring skill develops.

What is the exterior finish and does it affect performance?

The exterior is a matte black powder coating. It does not affect pouring performance and is intended to maintain a clean appearance during regular use.

The WPM Model #27, known as Small Blankenburg, is a 10oz (300ml) milk pitcher built for small format espresso drinks served under 6oz, including cortados, piccolo lattes, Gibraltars, and macchiatos. It uses WPM's #07 spout in a 10oz format, a narrower profile designed to slow the flow rate at the pour point and improve placement accuracy in smaller cups. For baristas working with delicate, low volume drinks, this pitcher trades raw flow for control.

Why You'll Love It

• Named Small Blankenburg by 2025 US Barista Champion Kay Cheon, connecting the pitcher to a real story behind the Slow Pour Supply and WPM partnership.
• WPM's #07 narrow spout reduces flow rate at the pour point, giving finer control when pouring into cups under 6oz.
• Signature WPM slanted top design angles the pour edge toward a single exit point for consistent flow.
• Wide body relative to its 10oz capacity allows the pitcher to hold enough milk to steam properly without the volume limits of a taller, narrower shape.
• Full loop handle accommodates multiple grip positions for different pouring styles.
• Sized specifically for drinks under 6oz, avoiding the compromises of using a larger pitcher for small format pours.

Recommended For

• Cortados.
• Piccolo lattes.
• Gibraltars.
• Macchiatos.
• Any milk beverage served under 6oz.
• Baristas refining precision pours on small format drinks.
• Home baristas making single shot milk drinks.

About the Collaboration

The Small Blankenburg name comes from a collaboration between Slow Pour Supply and Kay Cheon, the 2025 US Barista Champion. When Kay approached Slow Pour with an idea for a pitcher built around barista competition needs, the team worked with WPM, a leading global pitcher manufacturer, to develop a matte white finish designed to resist the fingerprints and milk stains that can cost points on the competition stage.

The name itself is a tribute rather than a technical label. It honors Mark Blankenburg, the milk delivery driver for Dune Coffee Roasters, recognizing the people behind the scenes who support the coffee industry. The Model #27 carries that name and finish in the 10oz narrow spout format, sized for small format drinks rather than the larger service pours the Blankenburg line also covers.

Design Features

WPM #07 Narrow Spout

The #07 spout is one of several spout profiles WPM produces across its pitcher line. Its narrower diameter reduces the flow rate at the pour point, which gives the barista more time and control when placing milk into a small cup.

WPM Slanted Top Design

The slanted top angles the pour edge rather than keeping it flat, directing milk toward a single exit point. This supports a more consistent stream and makes it easier to control where the pour lands.

Wide Body Profile

The body is wide relative to its 10oz capacity. This allows the pitcher to hold enough milk to steam properly without the narrow, tall shape that can limit steaming volume in smaller pitchers.

Full Loop Handle

The full loop handle is sized to accommodate different grip positions, letting baristas choose the hold that works best for their pouring technique.

Performance

Recommended Drink Sizes

The 10oz (300ml) capacity is built around drinks served under 6oz, including cortados, piccolo lattes, Gibraltars, and macchiatos.

Pouring Characteristics

The narrow #07 spout and slanted top work together to slow the flow rate and concentrate the pour at a single point, giving the barista more control over placement in small cups where precision matters more than volume.

Specifications

Specification	Details
Brand	WPM
Model	#27
Name	Small Blankenburg
Spout Type	WPM #07 spout, 10oz format
Volume	10oz / 300ml, for drinks under 6oz
Weight	221g
Material	Interior: 304 (18/8) stainless steel, uncoated, food-safe. Exterior: matte white powder coat.
Care	Hand wash and wipe dry
Origin	China

What's Included

• 1 x WPM Model #27 Milk Pitcher (Small Blankenburg).

Care & Maintenance

Hand wash the pitcher with warm water and a mild detergent after each use. Dry it immediately with a soft towel and store it right side up to prevent water spots on the stainless steel interior. Avoid abrasive pads or harsh chemicals, which can damage the matte white exterior finish over time.

Frequently Asked Questions

What drinks is the Small Blankenburg pitcher designed for?

It is built for small format espresso drinks served under 6oz, including cortados, piccolo lattes, Gibraltars, and macchiatos.

Why does the WPM #07 spout matter for small drinks?

The narrower spout reduces the flow rate at the pour point, giving more control over placement when pouring into smaller cups.

Where does the name Small Blankenburg come from?

The name was given by 2025 US Barista Champion Kay Cheon as part of a collaboration with Slow Pour Supply and WPM. It honors Mark Blankenburg, the milk delivery driver for Dune Coffee Roasters.

Is this pitcher too small to steam milk properly?

No. The body is wide relative to its 10oz capacity, which allows it to hold enough milk to steam correctly without the volume constraints of a narrower, taller pitcher.

How should I care for the matte white finish?

Hand wash with warm water and a mild detergent, then dry immediately with a soft towel. Avoid abrasive pads and harsh chemicals to keep the finish looking clean.

The WPM 10oz Latte Art Pitcher with Wide Spout in Cinder is built for small milk based espresso drinks, where precise pour placement matters more than volume. Finished in a matte Cinder exterior, it pairs WPM's signature slanted top with a wide diameter body and a WPM #06 spout, giving baristas a compact tool suited to macchiatos, cortados, and piccolos.

Built on WPM's proven #26 pitcher body, Cinder combines a food-grade stainless steel interior with a durable powder-coated exterior. The wide diameter body leaves extra room for steaming despite the pitcher's compact size, and the full handle supports multiple grip styles throughout the pour.

WHY YOU'LL LOVE IT

- Compact 10oz (300ml) capacity sized for small milk based espresso drinks.

- WPM #06 round spout from the Push and Flow series delivers a moderate, consistent flow suited to continuous pouring.

- Signature slanted top brings the milk stream closer to the crema layer sooner, producing fuller patterns with higher contrast.

- Wide diameter body leaves extra room for steaming despite the pitcher's compact size.

- Full handle accommodates multiple grip styles for comfort and stability during the pour.

- Matte Cinder exterior, an ash gray finish with a red hue.

RECOMMENDED FOR

- Macchiato, cortado, and piccolo service.

- Continuous pouring rather than edge-controlled drag techniques.

- Hearts, wing base tulips, stacked tulips, and slozettas.

- Baristas at beginner and up skill levels building pattern control.

DESIGN PHILOSOPHY

Cinder follows WPM's approach of pairing a proven pitcher body with a spout profile matched to a specific pour volume. The WPM #06 spout belongs to WPM's Push and Flow series, built for continuous pouring rather than edge-controlled drag techniques, and keeps flow moderate and consistent rather than fast.

Fitted to the 10oz #26 body, the same #06 spout reads proportionally wider than it does on WPM's larger-format pitchers, though the flow itself matches other #06 spouts in the line. The slanted top, a detail original to WPM's pitcher design, angles the stream toward the crema layer sooner, giving Cinder the same fuller, higher contrast patterns found across WPM's slanted top pitchers.

The name Cinder, an ash gray finish with a red hue, is credited to Morgan Eckroth.

DESIGN FEATURES

WPM #06 ROUND SPOUT

The #06 spout is part of WPM's Push and Flow series, developed for continuous pouring rather than edge-controlled drag techniques. It produces a moderate, consistent flow that gives baristas time to place milk accurately. At this 10oz volume, it suits hearts, wing base tulips, stacked tulips, and slozettas, and its forgiving flow makes it accessible to beginner and up skill levels while still supporting more advanced hybrid techniques as skill develops.

SIGNATURE SLANTED TOP

The slanted top is original to WPM's pitcher design and directs the milk stream at an angle that reaches the crema layer sooner. This reduces the tilt needed to start the pour, letting the spout sit closer to the surface and producing fuller patterns with higher contrast.

WIDE BODY DIAMETER

Relative to its 10oz capacity, the pitcher has a wide body diameter. This gives steaming milk more room to move during texturing, supporting smoother microfoam even in a pitcher sized for small pours.

FULL HANDLE

The full loop handle is sized to accommodate a range of grip styles. It keeps the pitcher stable through the full motion of a pour, from initial tilt to the final finishing lines.

CINDER MATTE FINISH

The exterior is finished in Cinder, an ash gray powder coating with a red hue, applied over food-grade stainless steel. The coating resists dings and helps the pitcher hold its shape under the repeated handling of daily café use.

304 (18/8) STAINLESS STEEL CONSTRUCTION

The pitcher is built from 304 (18/8) food-grade stainless steel. The interior is left uncoated, keeping it food safe and easy to clean after each use.

PERFORMANCE

RECOMMENDED DRINK SIZES

The 10oz (300ml) capacity is sized for cups under 6oz, including macchiato, cortado, and piccolo. This keeps the milk volume matched to the cup, avoiding excess steamed milk left over after the pour.

POURING CHARACTERISTICS

The WPM #06 spout produces a moderate, consistent flow built for continuous pouring rather than edge-controlled drag techniques. Combined with the slanted top, this supports hearts, wing base tulips, stacked tulips, and slozettas.

WORKFLOW

The spout's moderate, forgiving flow makes Cinder accessible to baristas at a beginner-plus skill level who are building pattern control. It also gives more experienced baristas a dependable option for small-format, continuous pours where consistency matters more than flow rate.

SPECIFICATIONS

WHAT'S INCLUDED

- 1 x WPM 10oz Latte Art Pitcher with Wide Spout in Cinder.

CARE & MAINTENANCE

Hand wash the pitcher with warm water and a mild detergent after each use, focusing on the interior where milk residue collects. Dry it immediately with a soft cloth to keep the matte Cinder finish free of water spots. Avoid abrasive pads, harsh chemicals, or prolonged soaking, since milk's acidity can wear down stainless steel's protective layer over time if residue is left to sit.

FREQUENTLY ASKED QUESTIONS

WHAT SIZE DRINKS IS THIS PITCHER DESIGNED FOR?

The 10oz (300ml) capacity is designed for cups under 6oz, such as macchiato, cortado, and piccolo.

WHAT SPOUT DOES THIS PITCHER USE, AND WHAT PATTERNS DOES IT SUPPORT?

It uses the WPM #06 round spout from WPM's Push and Flow series. At this volume, it suits hearts, wing base tulips, stacked tulips, and slozettas.

IS THIS PITCHER SUITABLE FOR BEGINNERS?

Yes. The #06 spout's moderate, consistent flow is forgiving during the pour, making it accessible to beginner and up skill levels while still supporting more advanced hybrid techniques as skill develops.

DOES THE WIDE BODY DIAMETER AFFECT STEAMING?

Yes. The wide diameter relative to the 10oz capacity gives milk more room to move during steaming, which supports smoother microfoam despite the pitcher's compact size.

WHERE DOES THE NAME CINDER COME FROM?

Cinder, an ash gray finish with a red hue, is credited to Morgan Eckroth.

HOW SHOULD I CLEAN AND MAINTAIN THE FINISH?

Hand wash with warm water and mild detergent, then dry immediately with a soft cloth. Avoid abrasive pads and prolonged soaking to protect both the interior stainless steel and the matte Cinder exterior.

The WPM 10oz Latte Art Pitcher with Wide Spout in Cinder brings WPM's proven slanted top design to a compact, cup-matched size. Between the moderate flow of the #06 spout and the wide body diameter, it gives baristas a dependable tool for continuous, small-format pours in daily service or while building pattern control.

A latte art pitcher in Hope, sized for small milk based drinks and built for steady, consistent pours. The WPM 10oz Latte Art Pitcher with Wide Spout in Hope holds 10oz (300ml) of milk and combines WPM's signature slanted top with a wide diameter body and a full handle. The pitcher uses a WPM #06 round spout and is finished in a gloss Hope exterior, a pink powder coating unique to this color series.

The wide diameter body leaves additional room for the milk to move during steaming, while the full handle supports a range of grip styles throughout the pour. WPM's slanted top directs the milk stream at an angle that reaches the crema layer sooner, producing fuller, higher contrast patterns without excessive tilt.

WHY YOU'LL LOVE IT

–       Compact 10oz body sized for macchiato, cortado, and piccolo pours.

–       WPM #06 round spout delivers a moderate, consistent flow for controlled placement.

–       Signature slanted top brings the milk stream closer to the crema, reducing the tilt needed to start a pour.

–       Wide body diameter gives steaming milk extra room to move, supporting smoother microfoam.

–       Full handle accommodates a range of grip styles for comfort and stability during the pour.

–       Gloss Hope finish gives the exterior a distinct, vibrant pink appearance.

RECOMMENDED FOR

–       Macchiato, cortado, and piccolo service.

–       Hearts, stacked tulips, and wing based tulips.

–       Baristas building pattern control before moving to narrower or wider spout profiles.

–       Cafes seeking a distinct color option for small format pours.

DESIGN PHILOSOPHY

Hope belongs to WPM's color series, which pairs the brand's proven pitcher bodies with distinct exterior finishes rather than changing the underlying engineering. Model #26 carries the Hope finish in a 10oz format, and the same color is also available in a 15oz pitcher fitted with a WPM #06 round spout, giving cafes a matching set across pour volumes.

At 10oz, the Hope pitcher keeps the #06 spout's round profile and moderate, consistent flow, though the opening reads proportionally wider on this smaller body than it does on WPM's larger pitchers. The spout belongs to WPM's Push and Flow series, built for continuous pouring rather than the edge controlled drag techniques used with narrower competition spouts.

DESIGN FEATURES

WPM SIGNATURE SLANTED TOP

WPM's slanted top is original to the brand's pitcher line and angles the milk stream toward the crema surface sooner than a flat top design. This reduces the tilt needed to begin a pour, letting the spout sit closer to the surface for finer detail and higher contrast patterns.

WPM #06 ROUND SPOUT

The #06 spout is part of WPM's Push and Flow series, designed for continuous pouring with a moderate, consistent flow rather than a fast or narrow one. On this 10oz body, the opening reads proportionally wider than it does on larger WPM pitchers, though the flow rate matches other #06 spouts in the line. The round profile suits hearts, stacked tulips, and wing based tulips, and its forgiving flow makes it a practical option for baristas developing pattern control.

WIDE BODY DIAMETER

Relative to its 10oz capacity, the pitcher has a wider body diameter. This gives steaming milk more room to move during texturing, supporting smoother microfoam even at this compact volume.

FULL HANDLE

The full loop handle is sized to accommodate a range of grip styles. It keeps the pitcher stable through the full motion of a pour, from initial tilt to finishing lines.

GLOSS HOPE FINISH

The exterior is finished in Hope, a gloss pink powder coating applied over a food grade stainless steel body. The gloss finish gives the pitcher a distinct, vibrant appearance that sets it apart within WPM's color series.

PERFORMANCE

RECOMMENDED DRINK SIZES

The 10oz (300ml) capacity is sized for cups under 6oz, including macchiato, cortado, and piccolo. At this volume, there is not enough milk for hybrid, multi stage pours.

POURING CHARACTERISTICS

The WPM #06 spout produces a moderate, consistent flow that favors control over speed. Paired with the slanted top, this supports precise placement for hearts, stacked tulips, and wing based tulips.

WORKFLOW

The spout's moderate, forgiving flow suits baristas at a beginner and up skill level, while still rewarding more precise base and layering technique as skill develops. It also gives experienced baristas a dependable option for small format service pours.

SPECIFICATIONS

WHAT'S INCLUDED

–       1 x WPM 10oz Latte Art Pitcher with Wide Spout in Hope.

CARE & MAINTENANCE

Hand wash the pitcher with warm water and a mild detergent after each use. Dry it immediately with a soft cloth to keep the gloss finish free of water spots. Avoid abrasive pads, harsh chemicals, or prolonged soaking, since milk residue left to sit can affect both the interior stainless steel and the exterior finish over time.

FREQUENTLY ASKED QUESTIONS

WHAT SIZE DRINKS IS THIS PITCHER DESIGNED FOR?

The 10oz (300ml) capacity is designed for cups under 6oz, such as macchiato, cortado, and piccolo.

WHAT SPOUT DOES THIS PITCHER USE, AND WHAT PATTERNS DOES IT SUPPORT?

It uses the WPM #06 round spout from WPM's Push and Flow series. At this volume, it suits hearts, stacked tulips, and wing based tulips.

IS HOPE AVAILABLE IN OTHER SIZES?

Yes. Hope is also available in a 15oz pitcher fitted with a WPM #06 round spout.

IS THIS PITCHER SUITABLE FOR BEGINNERS?

Yes. The #06 spout's moderate, consistent flow is forgiving during the pour, making it a practical starting point for baristas building pattern control.

HOW SHOULD I CLEAN AND MAINTAIN THE FINISH?

Hand wash with warm water and mild detergent, then dry immediately with a soft cloth. Avoid abrasive pads and prolonged soaking to protect both the interior stainless steel and the gloss exterior.

The WPM 10oz Latte Art Pitcher with Wide Spout in Hope brings WPM's proven slanted top design to a compact, cup matched size with a distinct gloss finish. Between the moderate flow of the #06 spout and the wider body diameter, it gives baristas a dependable tool for precise, small format pours in daily service or while building pattern control.

A round-spout latte art pitcher in matte black, sized for small milk based drinks and precise pour placement. The 10oz Latte Art Pitcher with Wide Spout in Black pairs WPM's signature slanted top with a compact, wide-diameter body, giving baristas a practical tool for macchiatos, cortados, and piccolos where careful placement matters more than volume.

Built on WPM's proven #26 pitcher body, this matte black edition combines a food-grade stainless steel interior with a durable powder-coated exterior. The result is a pitcher that holds its finish through daily service while keeping pours controlled at small volumes.

Why you'll love it

– Compact 10oz body sized for macchiato, cortado, and piccolo pours.

– WPM #06 round spout delivers a moderate, consistent flow for precise placement.

– Signature slanted top brings the milk stream closer to the crema surface, reducing the tilt needed to start a pour.

– Wide body diameter supports easier steaming and milk texturing despite the pitcher's compact size.

– Full handle accommodates multiple grip styles for comfort and stability.

– Matte black powder coated exterior resists dings and holds its shape under repeated daily use.

Recommended for

– Macchiato, cortado, and piccolo service.

– Precise milk placement in small-format pours.

– Hearts, stacked tulips, and wing base tulips.

– Baristas learning pattern control before moving to narrower or wider spout profiles.

Design philosophy

This pitcher reflects WPM's long-standing approach to latte art equipment: pair a reliable, well-tested body with a spout profile matched to a specific pour volume. The WPM #06 spout belongs to WPM's Push and Flow, Service Pour series, developed to keep milk flow moderate and consistent rather than fast, which suits smaller cups where overpouring is easy.

Fitted to the 10oz body, the same #06 spout reads proportionally wider than it does on larger pitchers, while keeping its round profile and predictable flow. The slanted top, a detail original to WPM's pitcher line, angles the stream toward the crema sooner, so the barista does not have to tilt the pitcher as far to begin a pour.

Design features

WPM #06 round spout

The #06 spout is part of WPM's Push and Flow, Service Pour lineup. It produces a moderate, consistent flow rather than a fast or narrow one, which gives baristas more time to place milk accurately in small cups. At this 10oz volume, the spout suits hearts, stacked tulips, and wing base tulips, and its forgiving flow makes it a practical starting point for beginner and beginner-plus baristas building pattern control.

Signature slanted top

The slanted top is original to WPM's pitcher design and directs the milk stream at an angle that reaches the crema surface sooner. This reduces the tilt needed to start the pour, letting the spout sit closer to the surface for finer detail and higher contrast patterns.

Wide body diameter

Relative to its 10oz capacity, the pitcher has a wider body diameter. This gives steaming milk more room to move during texturing, supporting smoother microfoam even in a pitcher sized for small pours.

Full handle

The full loop handle is sized to accommodate a range of grip styles. It keeps the pitcher stable through the full motion of a pour, from initial tilt to the final finishing lines.

Matte black powder coated finish

The exterior is finished with a matte black powder coating over food-grade stainless steel. The coating resists dings and helps the pitcher hold its shape under the repeated handling of daily café use.

304 (18/8) stainless steel construction

The pitcher is built from 304 (18/8) food-grade stainless steel. The interior is left uncoated, keeping it food safe and easy to clean after each use.

Performance

Recommended drink sizes

The 10oz (300ml) capacity is sized for cups under 6oz, including macchiato, cortado, and piccolo. This keeps the milk volume matched to the cup, avoiding excess steamed milk left over after the pour.

Pouring characteristics

The WPM #06 spout produces a moderate, consistent flow that favors control over speed. Combined with the slanted top, this supports precise placement and finer detail work at small pour volumes, including hearts, stacked tulips, and wing base tulips.

Workflow

The spout's moderate, forgiving flow makes it a practical choice for baristas at a beginner-plus skill level who are building pattern control. It also gives more experienced baristas a dependable option for small-format service pours where consistency matters more than flow rate.

Specifications

What's included

– 1 x 10oz Latte Art Pitcher with Wide Spout in Matte Black.

Care & maintenance

Hand wash the pitcher with warm water and a mild detergent after each use, focusing on the interior where milk residue collects. Dry it immediately with a soft cloth to keep the matte black finish free of water spots. Avoid abrasive pads, harsh chemicals, or prolonged soaking, since milk's acidity can wear down stainless steel's protective layer over time if residue is left to sit.

Frequently asked questions

What size drinks is this pitcher designed for?

The 10oz (300ml) capacity is designed for cups under 6oz, such as macchiato, cortado, and piccolo.

What spout does this pitcher use, and what patterns does it support?

It uses the WPM #06 round spout from WPM's Push and Flow, Service Pour series. At this volume, it suits hearts, stacked tulips, and wing base tulips.

Is this pitcher suitable for beginners?

Yes. The #06 spout's moderate, consistent flow is forgiving during the pour, making it a practical starting point for learning pattern control before moving to narrower or wider spout profiles.

Does the wider body diameter affect steaming?

Yes. The wider diameter relative to the 10oz capacity gives milk more room to move during steaming, which supports smoother microfoam despite the pitcher's compact size.

How should I clean and maintain the finish?

Hand wash with warm water and mild detergent, then dry immediately with a soft cloth. Avoid abrasive pads and prolonged soaking to protect both the interior stainless steel and the matte black exterior.

The 10oz Latte Art Pitcher with Wide Spout in Matte Black brings WPM's proven slanted top design to a compact, cup-matched size. Between the moderate flow of the #06 spout and the wider body diameter, it gives baristas a dependable tool for precise, small-format pours in daily service or while building pattern control.

A latte art pitcher in Peony, sized for small milk based drinks and built for steady, consistent pours. The WPM 10oz Latte Art Pitcher with Wide Spout in Peony holds 10oz (300ml) of milk and combines WPM's signature slanted top with a wide diameter body and a full handle. The pitcher uses a WPM #06 round spout and is finished in a matte Peony exterior, a pink powder coating unique to this color series.

The wide diameter body leaves additional room for the milk to move during steaming, while the full handle supports a range of grip styles throughout the pour. WPM's slanted top directs the milk stream at an angle that reaches the crema layer sooner, producing fuller, higher contrast patterns without excessive tilt.

WHY YOU'LL LOVE IT

–       Compact 10oz body sized for macchiato, cortado, and piccolo pours.

–       WPM #06 round spout delivers a moderate, consistent flow for controlled placement.

–       Signature slanted top brings the milk stream closer to the crema, reducing the tilt needed to start a pour.

–       Wide body diameter gives steaming milk extra room to move, supporting smoother microfoam.

–       Full handle accommodates a range of grip styles for comfort and stability during the pour.

–       Matte Peony finish gives the exterior a distinct, vibrant pink appearance.

RECOMMENDED FOR

–       Macchiato, cortado, and piccolo service.

–       Hearts, stacked tulips, and wing based tulips.

–       Baristas building pattern control before moving to narrower or wider spout profiles.

–       Cafes seeking a distinct color option for small format pours.

DESIGN PHILOSOPHY

Peony belongs to WPM's color series, which pairs the brand's proven pitcher bodies with distinct exterior finishes rather than changing the underlying engineering. Model #26 carries the Peony finish in a 10oz format, and the same color is also available in a 15oz pitcher fitted with a WPM #06 round spout, giving cafes a matching set across pour volumes.

At 10oz, the Peony pitcher keeps the #06 spout's round profile and moderate, consistent flow, though the opening reads proportionally wider on this smaller body than it does on WPM's larger pitchers. The spout belongs to WPM's Push and Flow series, built for continuous pouring rather than the edge controlled drag techniques used with narrower competition spouts.

DESIGN FEATURES

WPM SIGNATURE SLANTED TOP

WPM's slanted top is original to the brand's pitcher line and angles the milk stream toward the crema surface sooner than a flat top design. This reduces the tilt needed to begin a pour, letting the spout sit closer to the surface for finer detail and higher contrast patterns.

WPM #06 ROUND SPOUT

The #06 spout is part of WPM's Push and Flow series, designed for continuous pouring with a moderate, consistent flow rather than a fast or narrow one. On this 10oz body, the opening reads proportionally wider than it does on larger WPM pitchers, though the flow rate matches other #06 spouts in the line. The round profile suits hearts, stacked tulips, and wing based tulips, and its forgiving flow makes it a practical option for baristas developing pattern control.

WIDE BODY DIAMETER

Relative to its 10oz capacity, the pitcher has a wider body diameter. This gives steaming milk more room to move during texturing, supporting smoother microfoam even at this compact volume.

FULL HANDLE

The full loop handle is sized to accommodate a range of grip styles. It keeps the pitcher stable through the full motion of a pour, from initial tilt to finishing lines.

MATTE PEONY FINISH

The exterior is finished in Peony, a matte pink powder coating applied over a food grade stainless steel body. The matte finish gives the pitcher a distinct, vibrant appearance that sets it apart within WPM's color series.

The name Peony, a fuchsia pink finish, is credited to Amy Smithwick.

PERFORMANCE

RECOMMENDED DRINK SIZES

The 10oz (300ml) capacity is sized for cups under 6oz, including macchiato, cortado, and piccolo. At this volume, there is not enough milk for hybrid, multi stage pours.

POURING CHARACTERISTICS

The WPM #06 spout produces a moderate, consistent flow that favors control over speed. Paired with the slanted top, this supports precise placement for hearts, stacked tulips, and wing based tulips.

WORKFLOW

The spout's moderate, forgiving flow suits baristas at a beginner and up skill level, while still rewarding more precise base and layering technique as skill develops. It also gives experienced baristas a dependable option for small format service pours.

SPECIFICATIONS

WHAT'S INCLUDED

–       1 x WPM 10oz Latte Art Pitcher with Wide Spout in Peony.

CARE & MAINTENANCE

Hand wash the pitcher with warm water and a mild detergent after each use. Dry it immediately with a soft cloth to keep the matte finish free of water spots. Avoid abrasive pads, harsh chemicals, or prolonged soaking, since milk residue left to sit can affect both the interior stainless steel and the exterior finish over time.

FREQUENTLY ASKED QUESTIONS

WHAT SIZE DRINKS IS THIS PITCHER DESIGNED FOR?

The 10oz (300ml) capacity is designed for cups under 6oz, such as macchiato, cortado, and piccolo.

WHAT SPOUT DOES THIS PITCHER USE, AND WHAT PATTERNS DOES IT SUPPORT?

It uses the WPM #06 round spout from WPM's Push and Flow series. At this volume, it suits hearts, stacked tulips, and wing based tulips.

IS PEONY AVAILABLE IN OTHER SPOUT SHAPES?

Yes. Peony is also available in a 10oz pitcher fitted with a WPM #07 narrow spout.

IS THIS PITCHER SUITABLE FOR BEGINNERS?

Yes. The #06 spout's moderate, consistent flow is forgiving during the pour, making it a practical starting point for baristas building pattern control.

HOW SHOULD I CLEAN AND MAINTAIN THE FINISH?

Hand wash with warm water and mild detergent, then dry immediately with a soft cloth. Avoid abrasive pads and prolonged soaking to protect both the interior stainless steel and the matte exterior.

The WPM 10oz Latte Art Pitcher with Wide Spout in Peony brings WPM's proven slanted top design to a compact, cup matched size with a distinct matte finish. Between the moderate flow of the #06 spout and the wider body diameter, it gives baristas a dependable tool for precise, small format pours in daily service or while building pattern control.

A narrow-spout pitcher in a matte white finish, built for measured pours within a 15oz capacity.

WPM 15oz Latte Art Pitcher with Narrow Spout “Blankenburg” is a 15oz milk pitcher built for larger-volume pours. It includes a 6oz milk volume indicator marked on the interior wall, used to measure a pour amount without a separate vessel. It uses WPM’s #07 spout in a 15oz format, the same narrow spout profile used across other volumes in WPM’s line, and one of several spout profiles WPM produces across its pitcher catalog. The narrow #07 spout reduces the flow rate at the pour point and improves placement accuracy for fine-line work.

Blankenburg is built for larger-format pours where a 6oz portion is measured out from a 15oz working volume, a format commonly used for latte art practice and competition-style pours. Which specific drinks map to the 15oz capacity versus the 6oz indicator line has not been confirmed against supplier or brand guidance and should be verified before publishing, consistent with the use-case verification requirement for this product line.

Product Details

The Pitcher

The WPM 15oz Latte Art Pitcher with Narrow Spout “Blankenburg” uses WPM’s #07 spout in a 15oz format, the same narrow spout profile used on other 15oz latte art pitchers in WPM’s line, one of several spout profiles WPM produces across its catalog. The narrow spout reduces flow rate to improve placement accuracy. It features WPM’s slanted top design, where the pour edge is angled rather than flat, directing flow to a single exit point.

A milk volume indicator line is marked at 6oz on the interior wall, allowing dose efficiency. The body is wide in diameter relative to its 15oz capacity, which allows the pitcher to hold enough milk to steam properly without the volume constraint of a taller, narrower shape. The handle is a full loop, sized to accommodate different grip positions. The exterior is a white powder coat.

What’s in the Box

WPM Milk Pitcher, 15oz Blankenburg in Narrow Spout   x 1

The Core Component

Spout: WPM #07 spout in a 15oz format. Narrow diameter, one of several spout profiles WPM produces, reducing flow rate for controlled fine-line pours. Includes a 6oz milk volume indicator line. Uses WPM’s slanted top design.

Body: Wide diameter relative to capacity, holding a full 15oz for steaming.

Handle: Full loop handle, sized for multiple grip positions.

Specifications

Brand  WPM

Model  #07

Spout Type  WPM #07 spout, 15oz format

Name  Blankenburg (see note)

Volume  15oz; 6oz milk volume indicator for measured pours

Weight  263g 

Material  Interior: 304 18/8 stainless steel, uncoated, food-safe. Exterior: white powder coat – finish listed as both “matte” and “gloss” in source data; confirm actual finish with supplier before publishing (see note).

Care  Hand washed and wiped dry

Origin  China

Naming

Blankenburg is WPM’s name for this matte white colorway, a series of matte white pitchers with the color and name chosen by Kay Cheon. Additional background on the naming story is available in the tabbed content on the product page.

A versatile round-spout pitcher in matte black, balanced for multiple latte art patterns across standard cup sizes.

The WPM 15oz Latte Art Pitcher with Round Spout in Matte Black is a 15oz milk pitcher designed for standard latte and cappuccino pours. It uses WPM’s #06 spout, a round-profile spout that produces a broad, moderate pour stream compared to narrow spout profiles. This balanced flow makes it versatile across multiple latte art pattern types.

The pitcher includes a 6oz milk volume indent marked on the interior wall, allowing a set pour amount to be measured without a separate vessel, preventing milk waste. This format is commonly used for standard-size lattes and cappuccinos where baristas are learning and practicing pattern variation. The 15oz capacity provides ample milk for steaming and pouring.

Product Details

The Pitcher

The WPM 15oz Latte Art Pitcher with Round Spout in Matte Black uses WPM’s #06 spout in a 15oz format. It uses WPM’s slanted top design, an original WPM innovation where the pour edge is angled rather than flat. This slanted edge directs milk flow to a single exit point at an optimal angle, allowing the latte artist to reach the crema sooner and create fuller patterns with higher contrast. A 6oz milk volume indent is marked on the interior wall, allowing a set pour amount to be measured without a separate measuring vessel. The body is wide in diameter relative to its 15oz capacity, which allows the pitcher to hold enough milk to steam properly without the volume constraint of a taller, narrower shape. The handle is a full loop, sized to accommodate different grip positions. The exterior is finished in matte black.

Spout #06: Round Profile, Push and Flow

The #06 is a round-profile spout part of WPM’s Service Pour series. Round spouts produce a medium width ribbon of milk with a moderate, consistent flow rate. The #06 is categorized as a Push and Flow spout, meaning it’s designed for free-pour techniques using continuous, controlled milk movement rather than drag-and-draw styles.

Best for patterns: Wing base tulips, stacked hearts, medium-line rosettas (slozettas), and hybrid/combination pours. The moderate flow and broad pour stream make it forgiving for learning multiple pattern types.

Cup size fit: The 15oz pitcher volume is optimized for 6–8oz cups, making it ideal for flat white, small latte, and cappuccino. This mid-size cup format with the moderate #06 flow rate emphasizes precision and pattern definition in standard drinking vessels.

Skill level: Beginner friendly. The balanced flow of the round profile and the moderate volume of a 15oz pitcher make it a versatile choice for baristas who are learning and practicing multiple patterns without excessive difficulty.

What’s in the Box

WPM 15oz Latte Art Pitcher with Round Spout in Matte Black  x 1

The Core Component

Spout: WPM #06 spout in a 15oz format. Round profile produces a moderate, consistent flow rate — broader than narrow spout profiles but more controlled than wide profiles. Part of WPM Service Pour series with engineered lip design. Includes a 6oz milk volume indent. Uses WPM’s slanted top design, an original WPM innovation that directs milk flow at an optimal angle, allowing the barista to reach crema sooner for fuller patterns and higher contrast.

Body: Wide diameter relative to capacity, holding a full 15oz for steaming. Rounded interior bottom promotes smooth frothing, promoting breaking of large bubbles into silky microfoam.

Handle: Full loop handle, sized for multiple grip positions.

Specifications

Brand  WPM

Spout Type  WPM #06 spout, 15oz round-spout format; Push and Flow category; Service Pour series

Volume  15oz ; 6oz milk volume indent for measured pours; optimized for 6–8oz cups 

Material  Interior: 304 18/8 stainless steel, uncoated, food-safe. Exterior: matte black finish – coating material/process not specified in source data; confirm with supplier before publishing.

Care  Hand washed and wiped dry

Origin  China

A glossy white exterior makes this a perfect competition pitcher.

Product Details

• Narrow Spout for delicate fine lines - swipe to the last photo to see the comparison between our sharp spout and round spout

• Signature WPM slanted top design with 6 oz milk volume indicator

• Full Handle for any gripping style

• Material: 304 18/8 Stainless Steel. Uncoated, food-safe interior. Gloss white powder-coated exterior.

• Wide diameter

Matte Black is now available

Designed by WPM x airflowcoffee, this beautiful tamping mat is unlike any other.

 The grooved texture keeps coffee grounds away from your counter. At a small size of 5" x 5", this soft silicone mat adds a calming aesthetic to any brewing station. Heat resistant and dishwasher safe.

Available in sage green and off-white.

WPM Latte Art Cup
Crafted for Precision. Designed for Expression.

For optimal results, pair with the WPM 15oz Latte Art Pitcher - engineered for control and precision

Sought after by latte artists around the world, the WPM Latte Art Cup is designed to enhance both the visual and tactile experience of milk-based drinks. At 83.5 grams, its thoughtful form and performance-driven features provides the perfect vessel for those who take their latte art seriously.

Key Features:

• Expanded Surface Area
  The wide opening offers an ideal canvas for intricate and expressive designs, promoting better integration of espresso and milk foam.

• Enhanced Flow Dynamics
  A flatter internal base encourages smoother, more controlled pours - ideal for clean lines and well-defined shapes.

• Comfortable Handling
  Ergonomically shaped to fit securely in your hand, while staying cool to the touch.

• Optimized Capacity
  8 oz (220 mL) size, ideal for standard lattes and consistent practice.

Material: Ceramic

Weight: 83.5 grams

Rim Diameter: 4 inches

Handle (bottom): 1 inch

Designed by WPM, this oversized tamping mat isn’t just big- it’s built to take on more than your average mat!

The grooved texture keeps coffee grounds away from your counter. At a large size of 9.25" x 7.75", this soft silicone mat adds a calming aesthetic to any brewing station. Heat resistant and dishwasher safe.

Available in matte black.

The WPM Handleless Pitcher Sleeve features modern texture that is not only practical, but also built with comfort in mind.

High-quality matte texture Silicone provides a soft touch for your fingers and grooves to grip with comfort. Washable material is dishwasher friendly keeping it clean and sanitary.

Three sleek colors to choose from.

Tamping mat with matching texture is also available.

NOT ELIGIBLE FOR DISCOUNT -  Domestic shipping is included. 

Introducing the ZP-1 Single Dose Grinder by WPM, the epitome of precision and convenience in coffee grinding. Engineered with innovative features like tool-free disassembly for easy cleaning and unparalleled step-less grind adjustment, the ZP-1 offers a seamless coffee preparation experience. Its sophisticated design, coupled with high-performance components, ensures every coffee enthusiast can enjoy the perfect grind, every single time.

Unparalleled Step-less Grind Adjustment

This grinder features an advanced step-less grind adjustment system, allowing for precise calibration across a broad spectrum of grind sizes. This functionality enables users to achieve optimal grind settings tailored to various brewing methods, from ultra-fine grinds for espresso extraction to coarser textures suitable for French press brewing.

High-Performance Brushless DC Motor

The grinder is equipped with a high-torque, commercial-grade brushless DC motor that minimizes operational noise while maximizing efficiency. With adjustable grind speeds ranging from 600 to 1,300 RPM, users can select from 10 distinct settings to fine-tune the grind consistency, enhancing extraction quality and flavor profile.

Italian-Engineered 64mm Flat Burrs

Featuring precision-engineered 64mm flat burrs crafted in Italy, this grinder ensures an exceptionally uniform grind particle size. The design optimizes coffee extraction, facilitating enhanced flavor clarity and consistency in the final brew.

1-Step Quick Cleaning

The grinder’s components are designed for effortless disassembly, enabling a streamlined cleaning process that promotes optimal hygiene. This feature allows users to maintain the grinder with minimal downtime and effort.

Ultra Low Retention

Engineered for minimal retention, this grinder significantly reduces bean and grind size changes without the risk of taste crossover. This feature not only minimizes waste but also eliminates the need for purging between different coffee varieties. Additionally, the incorporation of anti-static technology prevents clumping, ensuring a uniform grind consistency.

Sleek Matte Black Aluminum Construction

Constructed from high-grade matte black aluminum, this coffee grinder combines robust durability with an elegant aesthetic. Its precision-engineered body ensures structural integrity while the compact design allows it to seamlessly integrate into any coffee setup without occupying excessive counter space.

Appearance: Aluminum body

Burr: 64mm Flat Burr

Grind range: Step-less adjustment; Espresso to French Press

Grinding speed: Adjustable RPM (600 to 1300)

Motor: Brushless DC motor

Hopper Capacity: 40g

Voltage: 100-120V~ / 50-60Hz

Power: 140-155W

Dimension: 277 (D) * 138 (W) * 330 (H) mm

Net Weight: 7.5kg

Upgrade your ZP-1 grinder with our meticulously engineered rose gold grind scale ring. 

Designed for precision and durability, this accessory not only enhances the grinder’s aesthetic appeal but also adds a refined, professional touch to your coffee workflow. Fabricated from high-grade materials with an anodized rose gold finish, the ring integrates seamlessly with the ZP-1, ensuring optimal alignment and a secure fit. A perfect combination of form and function, this upgrade delivers both visual sophistication and robust performance.

In this competition set, you will get: 

1. THREE April Plastic Brewers in the color of your choice
2. THREE packs of April Large size filters, designed to fit perfectly with the brewer

The 2.0 edition of the April Plastic Brewer. Made of improved plastic Makrolon®, the April plastic brewers keeps the brewing temperature more stable, enabling more consistency in the brewing process.

Features:

The bottom of the April Brewer features three "Filter Holder" wedges that hold your paper filter in place. This elevates the filter and enables a fast drawdown. The result is a perfectly balanced, transparent, and reliable taste experience.

The circular lines along the wall of the brewer allow more air pockets to be formed; enabling more air circulation. This helps brew consistency and enabling a cleaner, more transparent tasting cup.

FDA-approved Polycarbonate, Makrolon® has high thermo stability, enable you to maintain a consistent brewing temperature. 

As a safety precaution, all filters are final sale and not returnable.

What is the difference from the original version? 

• FDA-approved Polycarbonate, Makrolon® 2456 550115. This has increased the weight of the brewer by 7g and improved its ability to maintain a consistent brewing temperature. 
  
  
• Otherwise, the design is the same. 

Recommended Paper filter: April Filters or Kalita 155/185

April is a coffee roastery, rooted in Copenhagen, home to the Danish Roasting Champion 2019 and the 2nd place at World Brewers Cup 2019.

 As a safety precaution, all filters are final sale and not returnable.

April Plastic Brewers are crafted in Indonesia